Page Comparison

Type list

The stairs are organized under folders according to their types. The staircase to be drawn is selected under these folders.

Plan

The plan view of the selected stair is included.

Perspective

It has a three-dimensional view. It is possible to zoom in, zoom out, rotate the 3D image. In this way, the properties of the stairs can be examined in three dimensions.

Inverted stair

By marking it changes the exit direction of the stair flight.

Description

The description written for the stair is displayed on the Description line. User cannot intervene on this line.

Construction types

One of the straight, folded, bridge board and ramp type stair systems is selected by clicking with the left mouse button.

Riser parameters

D1 is the step cladding nose length, D2 is the riser cladding thickness, D3 is the step cladding thickness. If cladding is not wanted, these values ​​are entered as zero.

Stair cheek parameters

LK1 and LK2 determine the bridge board height. It is shown on the figure. The thickness parameter is the bridge board thickness.

Stair ID

The name of the stair is entered.

Stair elevation

The lower point of the stairs is the elevation measured from the floor base.

Baluster face count

The number of baluster surfaces determines the count of railing vertical surfaces (railing section). If the count of baluster surfaces is 4, the parapet cross section becomes square.

Don’t write step numbers after

The digits after the digit number entered here are not numbered on the stair.

Draw section line

If it is wanted to draw a section line on the stair, it is marked.

Structural material

Select the structual material to be used in the stair element from the list.

Finite element width

Enter the maximum finite element width to be taken as basis in shell calculation. The program analyzes shells by dividing them into trapezoidal form finite elements. Finite element width is automatically adjusted according to the shell shape, provided that it does not exceed the value entered in this row.

Draw concrete calculation lines

If it is wanted to show reinforced concrete calculation axes, it is marked.

Schematic drawing

Which elements of the stair are defined by line types and colors are shown in schematic drawings and numbering.

Linetypes

A separate line type is selected for the lines forming the stair in the plan. Clicking the down arrow buttons to the right of the boxes opens the list of line types. From this list, the wanted line type is selected by clicking with the left mouse button. The lines are numbered in red on the figure on the left.

Colors

A separate color is chosen for the lines forming the stair in the plan. The lines are numbered in blue on the figure to the left of the dialog. When the color box is clicked, the appropriate color is selected from the window that opens.

Label

By marking the label, the number of risers, riser height and step width are shown on the stair.

The font of the label font and the number of risers, the height and width of the digit is selected.

The text color of the label color and the number of risers, the height and width of the digit is selected.

The number of risers, the height of the digit and the height of the text of the width text are entered on the label height.

The total number of digits is unmarked, and the number of risers, riser height and step width are shown separately on each branch. If checked, total values ​​are shown.

Visual material

The material to be used on the body, cover, handrail and railing surfaces of the stairs is selected from the list. Surfaces are covered with the selected material and displayed as such in renderings.

Texture length is entered into the world length. For example; If 1 is entered, the selected material texture is taken as 1 meter and covered on the relevant walls.

The angle is the angle of the texture.

In the U and V offset, the motion value in the x and y plane of the texture is entered.

With U and V mirroring, the texture is symmetrical with respect to the y and x planes.

By selecting the single material option, the material selected in the "Body" is used on all surfaces of the wall.

Basic units

One of the selections is activated by clicking the left mouse button on the job.

Digit count

It determines how many digits will be shown after the comma. The desired number is selected from the list. For example, if 2 is selected, units will be shown as two digits after the comma. If 0 is selected, units will not be shown after the comma.

Fractions

It determines the precision of the dimension to be made in fractional inch format. In the list, there are options with a sensitivity of 1/2, ¼, 1/8, 1/16, 1/32, 1/34. If "no fraction" is selected, units will appear without fractions.

Rounding interval

It determines the rounding range of the measurement to be made in meters, centimeters or millimeters. If No rounding is selected, the dimensioning is done at exact value. As the range gets larger, the dimensioning is rounded up to the selected range.

Show zero unit

If it is not checked, it does not show the zero and point on the left in dimensioning. For example, it measures 0.20 as 20. If marked, the value 0.20 is scaled as 0.20.

Small fraction text

When fractional inch format is selected, determines the fractional part to display in upper / lower case. If it is checked, the fraction is slightly above the integer and small, if not, the fraction is shown the same size next to the integer.

Show zero foot

Determines whether 0 is displayed in the 0-foot gauge (less than 1 foot gauge). For example, if it is not checked, it will show a measure of 0 '- 15 "as -15". If marked, it shows as 0'-15 ".

Show zero inch on 0-1 inch range

For example, a dimension inch with a value of 8'-0 1/6 "is in the range 0-1. If the option is not ticked, the value 8'-0 1/6" will be displayed as 8'-. In other words, inch values ​​in the 0-1 range will not be displayed.

Show absolute zero inch

Determines whether to show zero inches in the dimension value where inches is absolute zero. For example, a dimension of exactly 10 'will be displayed as 10'-0 "if this option is selected. If not checked, it will be displayed as 10" -.

Handrail profiles

Select a handrail from the list of handrails by clicking with the left mouse button.

The selected handrail section is displayed on the handrail screen.

Baluster profiles

Select a baluster from the list of balusters by clicking the left mouse button.

The selected baluster image is displayed on the baluster screen.