...
Unstiffened Seated Connection Settings Dialog
Type and Placement Tab
...
Specifications |
|---|
Connection to support  Bolted or welded connection types are selected for the support connection. |
Connection to beam  Bolted or welded connection types are selected for the beam connection. |
Placement  Placement values are entered. The values to be entered are shown in the schematic drawing. |
Schematic drawing  Connection and placement values are shown on the schematic drawing. |
Preview  There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Angle Tab
...
Specifications |
|---|
Define plate geometry  If the option is selected, it is determined by entering the angle values. The values to be entered are shown in the schematic drawing. |
Use section  By selecting the option, one of the ready-made L profiles is selected from the list as an angle bracket. By clicking on the load section button, you can reach the ready section library and reach the list of American and European finished rolling sections and select from the list. |
Length  Angle length value is entered. |
Schematic drawing  Connection and plate values are shown on the schematic drawing. |
Preview There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Top/Bottom Notch Tabs
...
Specifications |
|---|
Notch  If the option is selected, notching is done according to the entered values. The values to be entered are shown in the schematic drawing. |
Left flange cut  If the option is selected, left flange cutting is made according to the entered values. The values to be entered are shown in the schematic drawing. |
Right flange cut  If the option is selected, right flange cutting is made according to the entered values. The values to be entered are shown in the schematic drawing. |
Schematic drawing  Connection, notching and cutting values are shown on the schematic drawing. |
Preview There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Stabilizer Tab
...
Specifications |
|---|
Connection to main part  Bolted or welded connection types are selected for the main part connection. |
Connection to connecting part  For the connected part connection, one of the bolted or welded connection types is selected. |
Type  It is selected whether the connection will be on the left or right or on the top of the beam body. |
Stabilizer Profile Tab
...
Specifications |
|---|
Define plate geometry  If the option is selected, it is determined by entering the angle values. The values to be entered are shown in the schematic drawing. |
Use section  By selecting the option, one of the ready-made L profiles is selected from the list as an angle bracket. By clicking on the load section button, you can reach the ready section library and reach the list of American and European finished rolling sections and select from the list. |
Length  Angle length value is entered. |
Schematic drawing  Connection and plate values are shown on the schematic drawing. |
Preview There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Stabilizer Bolts Tab
...
Specifications |
|---|
Horizontal arrangement  The horizontal arrangement settings (number of horizontal bolt columns, distance values ..) of the anchor bolts are entered. The values to be entered are shown in the schematic drawing. |
Group 1  Stabilizer bolts settings (number of lines, distance values ..) are entered. The values to be entered are shown in the schematic drawing. |
Bolt properties  The Hole and Bolt Parameters dialog is opened by clicking on the bolt properties button. The bolt properties are set in this dialog. |
Schematic drawing  Connection and bolt placement values are shown on the schematic drawing. |
Preview There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Beam Bolts Tab
...
Specifications |
|---|
Horizontal arrangement  Beam bolts horizontal arrangement settings (number of horizontal bolt columns, distance values ..) are entered. The values to be entered are shown in the schematic drawing. |
Group 1  Beam bolts settings (number of lines, distance values ..) are entered. The values to be entered are shown in the schematic drawing. |
Bolt properties The Hole and Bolt Parameters dialog is opened by clicking on the bolt properties button. The bolt properties are set in this dialog. |
Schematic drawing  Connection and bolt placement values are shown on the schematic drawing. |
Preview There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Welds Tab
In the welds tab, the weld properties of the connections given in the schematic representation are set.
...
Specifications |
|---|
Welds  The thickness, type and angle values of the welds to be made at the connections are given. The information on whether it will be done on the construction site or not is entered. |
Weld electrode  The strengths of the welding electrodes are defined in the design inputs. The strength of the main element in the weld joint is controlled under the condition that it has less strength than the weld strength. If necessary, click the list and define "Create New…". To create the welding electrode, give the information "Name" and "Weld metal tensile strength" in the dialog that opens after clicking "Create New". |
| title | Moreover |
|---|
Welding geometry is determined automatically by the program. These properties can be changed to easily determine the connection properties. Geometry features are in accordance with industry standards and in the form specified in AISC. |
Schematic drawing  Connection and source values are shown on the schematic drawing. |
Preview  There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Design Data Tab
...
In the design data, the plate material is defined.
...