This connection is an intersecting With the Continuous Beam Connection command, beam-beam connection is defined. It can be applied to one piece main beam and two piece beam connections.
...
Location of the Continuous Beam Connection Command
...
Continuous Beam Connection Settings Dialog
Flange Connection Type
...
Specifications |
|---|
Top flange connection type  Connection type is selected for the top header. |
Schematic drawing  Connection and placement values are shown on the schematic drawing. |
Preview  There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Plates Tab
...
Specifications |
|---|
Persistence plate  Persistance plate is determined by entering the value. The values to be entered are shown in the schematic drawing. |
Schematic drawing  Connection and plate values are shown on the schematic drawing. |
Preview There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Shear Type Tab
...
Specifications |
|---|
Shear connection type  The shear connection type is selected. |
Connection type  Welded or bolted connection types are selected. |
Bottom flange connection type  Connection type is selected for the bottom flange. |
Schematic drawing  Connection and plate values are shown on the schematic drawing. |
Preview There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Shear Plate Tab
...
Specifications |
|---|
Pressure plate  The pressure plate is determined by entering the value. The values to be entered are shown in the schematic drawing. |
General  The value is entered to determine the location of the plate according to the beam section. The values to be entered are shown in the schematic drawing. |
End plate  The end plate is determined by entering the value. The values to be entered are shown in the schematic drawing. |
Schematic drawing  Connection and plate values are shown on the schematic drawing. |
Preview There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Top Left/Top Right Notch Tab
...
Select options and enter values according to the given schematic figure.
...
Welds Tab
...
The weld properties of the connections given in the schematic representation are set in the Welds tab. Give the size, type, angle values and mark the option whether to weld under construction site conditions.
...
...
Specifications |
|---|
Notch  If the option is selected, notch is done according to the entered values. The values to be entered are shown in the schematic drawing. |
Left flange cut  If the option is selected, left flange cutting is made according to the entered values. The values to be entered are shown in the schematic drawing. |
Right flange cut  If the option is selected, right flange cutting is made according to the entered values. The values to be entered are shown in the schematic drawing. |
Schematic drawing  Connection, notching and cutting values are shown on the schematic drawing. |
Preview There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Welds Tab
...
Specifications |
|---|
Welds  The thickness, type and angle values of the welds to be made at the connections are given. The information on whether it will be done on the construction site or not is entered. |
Weld electrode  The strengths of the welding electrodes are defined in the design inputs. The strength of the main element in the weld joint is controlled under the condition that it has less strength than the weld strength. If necessary, click the list and define "Create New…". To create the welding electrode, give the information "Name" and "Weld metal tensile strength" in the dialog that opens after clicking "Create New". Welding geometry is determined automatically by the program. These properties can be changed to easily determine the connection properties. Geometry features are in accordance with industry standards and in the form specified in AISC. |
Schematic drawing |
...
 Connection and weld values are shown on the schematic drawing. |
Preview There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Top Left Flange Bolts Tab
...
Determine the count of bolts and the distances between bolts according to the schematic representation given.
Bolt properties: Bolt grade, bolt size and hole properties are set in bolt properties.
...
Specifications |
|---|
Horizontal arrangement  The horizontal arrangement distance value of the bolts is entered. The values to be entered are shown in the schematic drawing. |
Group 1  Distance values of bolts to beam and other bolts are entered. The values to be entered are shown in the schematic drawing. |
Bolt properties  The Hole and Bolt Parameters dialog is opened by clicking on the bolt properties button. The bolt properties are set in this dialog. |
Schematic drawing  Connection and bolt arrangement values are shown on the schematic drawing. |
Preview There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Top Right Flange Bolts Tab
...
Determine the count of bolts and the distances between bolts according to the schematic representation given.
Bolt properties: Bolt grade, bolt size and hole properties are set in bolt properties.
...
Specifications |
|---|
Horizontal arrangement The horizontal arrangement distance value of the bolts is entered. The values to be entered are shown in the schematic drawing. |
Group 1 Distance values of bolts to beam and other bolts are entered. The values to be entered are shown in the schematic drawing. |
Bolt properties The Hole and Bolt Parameters dialog is opened by clicking on the bolt properties button. The bolt properties are set in this dialog. |
Schematic drawing  Connection and bolt placement values are shown on the schematic drawing. |
Preview There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Assembly Plate Tab
...
Specifications |
|---|
Define plate geometry  If the option is selected, the assembly plate is determined by entering the values. The values to be entered are shown in the schematic drawing. |
Use section  By selecting the option, one of the ready-made L profiles is selected from the list as an assembly plate. By clicking on the Load section button, you can reach the ready section library and reach the list of American and European finished rolling sections and select from the list. |
Length  The assemblyplate length to be used is determined by entering the value. |
Schematic drawing  Connection and plate values are shown on the schematic drawing. |
Preview There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Bottom Left Flange Bolts Tab
...
Determine the count of bolts and the distances between bolts according to the schematic representation given.
Bolt properties: Bolt grade, bolt size and hole properties are set in bolt properties.
...
...
Specifications |
|---|
Horizontal arrangement  The horizontal arrangement distance value of the bolts is entered. The values to be entered are shown in the schematic drawing. |
Group 1  Distance values of bolts to beam and other bolts are entered. The values to be entered are shown in the schematic drawing. |
Bolt properties The Hole and Bolt Parameters dialog is opened by clicking on the bolt properties button. The bolt properties are set in this dialog. |
Schematic drawing  Connection and bolt arrangement values are shown on the schematic drawing. |
Preview There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Bottom Right Flange Bolts Tab
...
Determine the count of bolts and the distances between bolts according to the schematic representation given.
Bolt properties: Bolt grade, bolt size and hole properties are set in bolt properties.
...
Assembly Plate Tab
...
The geometry of the plate used is given or one of the L profiles in the library can be used as a connection element with the Use Section option. If you check the plate geometry option, enter the plate dimensions according to the schematic representation.
...
...
Specifications |
|---|
Horizontal arrangement The horizontal arrangement distance value of the bolts is entered. The values to be entered are shown in the schematic drawing. |
Group 1 Distance values of bolts to beam and other bolts are entered. The values to be entered are shown in the schematic drawing. |
Bolt properties The Hole and Bolt Parameters dialog is opened by clicking on the bolt properties button. The bolt properties are set in this dialog. |
Schematic drawing  Connection and bolt arrangement values are shown on the schematic drawing. |
Preview  There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Design Data Tab
...
In the design data, the connection elements material is defined. The condition that the main element in the weld joint has less strength than the weld strength is controlled.
...
If necessary, click the list and define "Create New…". To create the connection elements material, give the information material definitions and values in the dialog that opens after clicking "Create New".
...