How does ideCAD control beam transverse reinforcement detailing according to ACI 318-19?
...
| Tip |
|---|
|
| Tip |
|---|
|
...
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
Download ideCAD for ACI 318-19 |
Notation
Ag = gross area of concrete section, in2
bw = web width or diameter of circular section, in.
bt = width of that part of cross section containing the closed stirrups resisting torsion, in.
d = distance from extreme compression fiber to centroid of longitudinal tension reinforcement, in.
db = nominal diameter of bar, wire, or prestressing strand, in
fc' = specified compressive strength of concrete, psi
√fc‘ = square root of specified compressive strength of concrete, psi
fy = specified yield strength of nonprestressed reinforcement,psi
fyt = specified yield strength of transverse reinforcement, psi
h = overall thickness, height, or depth of member, in.
ph = perimeter of centerline of outermost closed transverse torsional reinforcement, in.
s = center-to-center spacing of items, such as longitudinal reinforcement, transverse reinforcement, tendons, or anchors, in.
Ve = design shear force for load combinations including earthquake effects, lb
Vn = nominal shear strength, lb
Vs = nominal shear strength provided by shear reinforcement, lb
Vu = factored shear force at section, lb
ϕ = strength reduction factor
...
Details of transverse reinforcement are applied in accordance with Transverse Reinforcement per ACI 318-19 with ideCAD title.
Hoops
Hoops consist of a closed tie or continuously wound tie, which can consist of several reinforcement elements each having seismic hooks at both ends (Transverse Reinforcement per ACI 318-19 with ideCAD).
...
Shear reinforcement is provided using stirrups, hoops, or longitudinal bent bars. Also, additional shear reinforcement, called hanger reinforcement (ACI Fig R9.7.6.2.1), should be placed to transfer shear from the end of the supported beam. According to ACI R9.7.6.2.1 hanger reinforcement is not requredrequiredif the bottom of the supported beam is at or above middepth mid-depth of the supporting beam or if the factored shear transferred from the supported beam is less than 3√fc‘bwd.
According to ACI 9.7.6.2.2. , maximum shear reinforcement leg spacing along the beam's length of the beam and across the beam's width of the beam should be in accordance with given below.
Vs | Along length Maximum s, in. | Across length Maximum s, in. | ||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
|
| ||||||||||||||||||
|
|
|
Shear strength provided by bent-up longitudinal reinforcement is neglected.
...
If torsional reinforcement is required, transverse torsional reinforcement should be closed stirrups satisfying Stirrups per ACI 318-19 with ideCAD or hoops.
According to ACI 9.7.6.3.2, transverse torsional reinforcement should extend it beyond the point required by the analysis by at least (bt + d) distance.
According to ACI 9.7.6.3.3, the maximum spacing of transverse torsional shoul should be the lesser of ph/8 and 12 in.
...
Transverse reinforcement is provided throughout the distance where longitudinal copression compression reinforcement is required. Closed stirrups or hoops provide lateral support of longitudinal compression reinforcement.
According to ACI 9.7.6.4.2; , transverse reinforcement size should be at least one of the two conditions below,
No. 3 for longitudinal bars No.10 and smaller
No. 4 for longitudinal bars No.11 and larger
According to ACI 9.7.6.4.3; , the maximum spacing of transverse reinforcement should not exceed the least of three conditions below,
16db of longitudinal reinforcement
48db of transverse reinforcement
Least dimension of the beam
According to ACI 9.7.6.4.4, Longitudinal compression reinforcement in each corner and alternative copression compression bar shall be arranged to be surrounded by transverse reinforcement around the corner with an included angle of not more than 135 degrees. Also, no bar shall be farther than 6 in. clear on each side along the transverse reinforcement from such an enclosed bar.
...
Reinfocement Reinforcement Limits for Beams of Earthquake Reistant -Resistant Structures
Ordinary moment frames
All the conditions described above are valid for beams of ordinary moment frames.
Intermediate moment frames
All the conditions described above are valid for beams of intermediate moment frames.
According to ACI 18.4.2.4, the hoop should be provided over a minimum length 2h measured from the face of the supporting member toward the midspan , at both ends of the beam. The first hoop should be located a length of at least 2 in. from the face of the supporting member. Spacing og The spacing of hoop should not exceed the smallest of values given below,
...
According to ACI 18.4.2.5, the spacing of transverse reinforcement should not exceed d/2 throughout the length of the beam.
According to ACI 18.4.2.6, if factored axial compressive force of beams exceed 0.10fc’Ag , transverse reinforcement required by ACI 18.4.2.5 shall conform to ACI 25.7.2.2and either ACI 25.7.2.3or ACI 25.7.2.4.
Special moment frames
All the conditions described above are valid for beams of special moment frames.
According to ACI 18.6.4.1, Hoops should be provide provided in the beam regions given below,
Over a length equal to twice the beam depth measured from the face of the supporting column toward the midspan , at both ends of the beam
Over lengths equal to twice the beam depth on both sides of a section where flexural yielding is likely to occur as a result of lateral displacements beyond the elastic range of behavior.
According to ACI 18.6.4.2, where hoops are required, primary longitudinal reinforcing bars should have lateral support in accordance with Transverse Reinforcement per ACI 318-19 with ideCAD title. The maximum spacing og of transversely supported flexural reinforcing bars are 14 in.
According to ACI 18.6.4.3, hoops in beams can consis consist of two reinforcement pieces of reinforcement. These pieces are a stirrup havin having seismic hooks at both ends and closed by a crosstie. If a slab confines the longitudinal reinforcing bars secured by the crossties are confined by a slab on only one side of the beam, the 90-degree hooks of the crossties shall be placed on that side.
...
According to ACI 18.6.4.7, if Pu≥ 0.10fc’Ag , hoops satisfying columns of special moment frames transverse reinforcement detailing should be provided along the lengths given in ACI 18.6.4.1. Along the remaining length, maximum hoop spacing s should be the smallest of the values given below,
...
If concrete cover over transverse reinforcement exceeds 4 in., additional transverse reinforcement having cover not exceeding 4 in. and spacing not exceeding 12 in. should be provided.
...
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
Download ideCAD for ACI 318-19 |
Next Topic
Reinforced Concrete Beam-Column Joint Shear Design per ACI 318-19 §15, §18.8