SymbolsSYMBOLSD = Strength Excess Coefficient
f d (µ, T ) = Design strength required of the carrier system depending on the predicted ductility capacity and period
f (T e ) = Linear (elastic) strength demand calculated for the carrier system
f y (µ k , T ) = Projected ductility capacity and yield strength depending on period
I = Building Importance Factor
R = Structural System Behavior Coefficient
R a ( T) =Projected ductility capacity and Seismic Load Reduction Coefficient depending on the period
R y (µ k , T) = Predicted ductility capacity and Yield Strength Reduction Coefficient depending on the period
T = Natural vibration period [s]
T B = Horizontal elastic design acceleration spectrum corner period [s]
µ k = ductility capacity prescribed for the carrier system
The basic seismic analysis procedure uses response spectra that are representative of, but substantially reduced from, the anticipated ground motions. As a result, at the MCER level of ground shaking, structural elements are expected to yield, buckle or otherwise behave inelastically. In the standard, such design forces are computed by dividing the forces that would be generated Cs = The seismic response coefficient
SD1 = The design spectral response acceleration parameter at a period of 1.0 s
SDS = The design spectral response acceleration parameter in the short period range
R = The response modification factor in Table 12.2-1
Ie = The Importance Factor
...
The seismic analysis procedure is performed with reduced response spectra. At MCER level of ground motion, structural elements are prospective to yield, buckle or behave inelastically. In ASCE 7-16, the response modification coefficient, R, is used to compute seismic design internal forces by dividing the forces. It is produced in a structure behaving elastically when subjected to the design earthquake ground motion by the response modification coefficient, R, and this design ground motion is taken as two-thirds of the MCER ground motion.
The intent purpose of R is to reduce the demand determined, assuming that the structure remains elastic at the design earthquake level, to target the development of the first significant yield. This reduction accounts computes for ductility demand of the displacement ductility demand, Rd, required by the structural system and the inherent overstrength, Ω, of the seismic
force-resisting system(SFRS) (Fig. C12.1-1). Significant A significant yield point is where the point where complete plastification of a critical region of the SFRS first occurs is completely plastic (e.g., formation of the first plastic hinge in a moment frame), and the stiffness of the SFRS to further increases increase in lateral forces decreases as continued inelastic behavior spreads
within the SFRS. This approach is consistent with suitable for member-level ultimate strength design practices. As such, first significant yield should not be misinterpreted as the point where first yield occurs in any member (e.g., 0.7 times the yield moment of a steel beam or either initial cracking or initiation of yielding in a reinforcing bar in a reinforced concrete beam or wall).
...
Fig. C12.1-1 shows the lateral force versus deformation relation for an archetypal moment frame used as an SFRS. Because of particular design rules and limits, including material strengths in excess of nominal or project-specific design requirements.
Due to the design rules and limits according to C12.9.1.3, including material strengths, structural elements are stronger by some degree than the required strength required by analysis. The maximum strength developed along the curve is substantially higher than that at first significant yield, and this margin point is referred to as the system overstrength capacity. The ratio of these strengths is denoted as , Ω. The system overstrength described above is the direct result of the overstrength of the elements that form the SFRS and , to a lesser extent, the lateral force distribution used to evaluate the inelastic force–deformation curve.
Structures typically have a much higher lateral strength than that specified as the minimum by the standard, and the first significant ASCE 7-16. The first yielding of structures may occur at lateral load levels that are 30% to 100% higher than the prescribed design seismic forces . If provided with adequate ductile detailing, redundancy, and regularity, full yielding of structures may occur at load levels that are two to four times the prescribed design force levels.
The energy dissipation resulting from hysteretic behavior can be measured as the area enclosed by the force–deformation curve of the structure as it experiences several cycles of excitation. Some structures have far more energy dissipation capacity than others. The extent of energy dissipation capacity available depends largely on the amount of stiffness and strength degradation the structure undergoes as it experiences repeated cycles of inelastic deformation. Fig. C12.1-2 shows representative load deformation curves for two simple substructures, such as a beam–column assembly in a frame. Hysteretic curve (a) in the figure represents the behavior of substructures that have been detailed for ductile behavior. The substructure can maintain almost all of its strength and stiffness over several large cycles of inelastic deformation. The resulting force–deformation “loops” are quite wide and open, resulting in a large amount of energy dissipation. Hysteretic curve (b) represents the behavior of a substructure that has much less energy dissipation than that for the substructure (a) but has a greater change in response period. The structural response is determined by a combination of energy dissipation and period modification.
...
by the standard.
...
Next Topic