Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 33 Next »

How does ideCAD design single plate connection according to AISC 360-16?


  • Single plate connection limit states checks and geometry checks are done automatically according to AISC 360-16?

  • The block shear limit state is checked automatically according to AISC 360-16.


Symbols

Ab: Non-threaded bolt web characteristic cross-sectional area
Ag: Gross area
An: Net cross-section area
Ae: Effective net cross-sectional area
Avg: Gross area under shear stress
Anv: Net area under shear stress
Ant: Net area under tensile stress
Aw: Cross-section web area
Cv: Coefficient of reduction for shear buckling
d: Characteristic diameter of the stem of the bolt (the diameter of the non-threaded stem of the bolt)
dh: Bolt hole diameter
Fnt: Characteristic tensile strength
F'nt: Reduced characteristic tensile stress obtained by considering the shear force effect
Fnv: Characteristic shear stress strength
frv: The greatest shear stress in the characteristic web area of ​​the bolt
Fy: Structural steel characteristic yield strength
Fu: Structural steel characteristic tensile strength
Fyb: Bolt characteristic yield strength
Fub: Bolt characteristic tensile strength
nsp: Number of slip planes
s: Distance between bolt-hole centers
L: Connector distance
Le: The distance from the center of the bolt hole to the edge of the assembled element
t: Plate thickness
Rnt: Characteristic tensile strength
Rnv: Characteristic shear strength
Ubs: A coefficient considering the spread of tensile stresses


Connection Geometry

Geometry Checks

Bolt Spacing

The distance between the centers of bolts is checked per AISC 360-16.

smin ≥ 3d       

AISC 360-16 J3.3

 

 

s

79.5 mm

 

 

d

20 mm

s =79.5 mm > smin = 3*20=60 mm

Horizontal Edge Distance

The distance from the center of the hole to the edge of the connected part in the horizontal direction is checked per AISC 360-16.

Leh ≥ Le-min     

AISC 360-16 J3.4

 

 

Leh

40 mm

Leh ≥ 2d = 2 * 20 = 40 mm conformity check for application

Le-min

26 mm

Minimum distance check according to AISC 360-16 Table J3.4

Vertical Edge Distance

The distance from the center of the hole to the edge of the connected part in the vertical direction is checked per AISC 360-16.

Lev ≥ Le-min     

AISC 360-16 J3.4

 

 

Lev

40 mm

Leh ≥ 2d = 2 * 20 = 40 mm conformity check for application

Le-min

26 mm

Minimum distance check according to AISC 360-16 Table J3.4

Weld Size

The minimum size of fillet welds is checked according to AISC 360-16 Table J2.4

w ≥ wmin     

AISC 360-16 Table J2.4

 

 

w

12.73 mm

 

wmin

5 mm

AISC 360-16 Table J2.4

Erection Stability

L ≥ hb/2

 

 

L

239 mm

 

 

hb

248.6 mm

L=239 > 248.6/2=124.3 mm

Strength Checks

Bolt Shear at Beam

  • The calculation is made using the Elastic method, one of the methods selected in the steel analysis settings tab. For the details of this check, AISC Manual 14th 7-8 is used as a reference.

  • In this check, the operation is performed on half of the symmetry axis, and it is calculated to form a force pair with the required force.

Ab

Fn=Fnv

 

Rn

 

Rn / Ω

 

Required

Available

Check

Result

34,318 kN

56,549 kN

0.607

Bolt Bearing on Beam

Bearing strength limit states of the plate that are “shear tear out” and “ovalization of bolt hole” for both end and inner bolts are checked according to AISC 360-16.

dh

20+2=22 mm

 

Lc,edge

 

Rn

AISC 360-16 J3-6a

Rn-edge

 

Lc,spacing

 

Rn-spacing

 

Rn

 

 

Rn / Ω

 

Required

Available

Check

Result

68,159 kN

185,487 kN

0.367

Bolt Bearing on Plate

Bearing strength limit states of the connection plate that are “shear tear out” and “ovalization of bolt hole” for both end and inner bolts are checked according to AISC 360-16.

dh

20+2=22 mm

 

Lc,edge

 

Rn

AISC 360-16 J3-6a

Rn-edge

 

Lc,spacing

 

Rn-spacing

 

Rn

 

Rn

 

Required

Available

Check

Result

68,159 kN

284,75 kN

0.239

Plate Shear Yield

In the case of the block shear limit state, the gross area yielding of the tensile plane is checked according to AISC 360-16.

Ag

 

Fy

235.359 N/mm2

 

Rn

AISC 360-16 J4-3

Rn

 

Required

Available

Check

Result

68,159 kN

270 kN

0.252

Beam Shear Rupture

In the case of the block shear limit state, the net area rupture of the tensile plane of the connection part is checked according to AISC 360-16.

Anv

 

Fu

362.846 N/mm2

 

Rn

AISC 360-16 J4-3

Rn / Ω

 

Required

Available

Check

Result

68,159 kN

176.213 kN

0.387

Plate Shear Rupture

In the case of the block shear limit state, the net area rupture of the tensile plane of the connection part is checked according to AISC 360-16.

Anv

 

Fu

362.846 N/mm2

 

Rn

AISC 360-16 J4-3

Rn / Ω

 

Required

Available

Check

Result

68,159 kN

218.143 kN

0.312

Plate Block Shear Rupture

The block shear limit state is checked according to AISC 360-16. All block shear modes combined with tensile failure on one plane and shear failure on a perpendicular plane are checked according to AISC 360-16.

Ag

 

Anv

 

Ant

 

Fy

235.359 N/mm2

 

Fu

362.846 N/mm2

 

Ubs

1.0

 

 

 

Rn

AISC 360-16 J4-3

Rn / Ω

 

Required

Available

Check

Result

68,159 kN

229.569 kN

0.297

Plate Flexural Buckling

Fy

235.359 N/mm2

 

t

12 mm

 

a

60 mm

 

L

239 mm

 

λ

 

Required

Available

Check

≤0.70

0.17

Plate Flexural Yield

dp

239 mm

 

Fy

235.359 N/mm2

 

tp

12 mm

 

a

60 mm

 

Rn

 

Rn / Ω

 

Required

Available

Check

Result

68,159 kN

223.92 kN

0.304

Weld Strength at Support

w

12.73 mm

 

FE

480 N/mm2

 

l

239 mm

 

e

60 mm

 

Rn

 

Rn / Ω

 

Required

Available

Check

Result

68,159 kN

421.131 kN

0.162



  • No labels