...
Specifications |
|---|
Define plate geometry  If the option is selected, it is determined by entering the angle values. The values to be entered are shown in the schematic drawing. |
Use section  By selecting the option, one of the ready-made L profiles is selected from the list as an angle bracket. By clicking on the load section button, you can reach the ready section library and reach the list of American and European finished rolling sections and select from the list. |
Length  Angle length value is entered. |
Schematic drawing  Connection and plate values are shown on the schematic drawing. |
Preview  There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Top Notch Tab
The notch geometry of the top of the beam element connected to the column is adjusted.
...
Bottom Notch Tab
The notch geometry of the bottom part of the beam element connected to the column is adjusted.
...
Support Bolts Tab
The properties of the bolts connecting the plate to the column are adjusted. The tab can be seen when the option with bolt to the support is selected from the type and layout tab.
...
Beam Bolts Tab
The properties of the bolts connecting the plate to the column are adjusted. The tab can be seen when the option with bolt to the support is selected from the type and layout tab.
...
Weldings Tab
The weld properties of the connections given in the schematic representation are set in the Welds tab. Give the size, type, angle values and mark the option whether to weld under construction site conditions.
...
Specifications |
|---|
Notch  If the option is selected, notching is done according to the entered values. The values to be entered are shown in the schematic drawing. |
Left flange cut  If the option is selected, left flange cutting is made according to the entered values. The values to be entered are shown in the schematic drawing. |
Right flange cut  If the option is selected, right flange cutting is made according to the entered values. The values to be entered are shown in the schematic drawing. |
Schematic drawing  Connection, notching and cutting values are shown on the schematic drawing. |
Preview There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Bottom Notch Tab
...
Specifications |
|---|
Notch If the option is selected, notching is done according to the entered values. The values to be entered are shown in the schematic drawing. |
Left flange cut If the option is selected, left flange cutting is made according to the entered values. The values to be entered are shown in the schematic drawing. |
Right flange cut If the option is selected, right flange cutting is made according to the entered values. The values to be entered are shown in the schematic drawing. |
Schematic drawing  Connection, notching and cutting values are shown on the schematic drawing. |
Preview There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Support Bolts Tab
...
Specifications |
|---|
Horizontal arrangement  Horizontal arrangement settings (number of horizontal bolt columns, distance values ..) of support bolts are entered. The values to be entered are shown in the schematic drawing. |
Group 1  Support bolts settings (number of lines, distance values ..) are entered. The values to be entered are shown in the schematic drawing. |
Bolt properties  The Hole and Bolt Parameters dialog is opened by clicking on the bolt properties button. The bolt properties are set in this dialog. |
Schematic drawing  Connection and bolt placement values are shown on the schematic drawing. |
Preview  There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Beam Bolts Tab
...
Specifications |
|---|
Horizontal arrangement Horizontal arrangement settings (number of horizontal bolt columns, distance values ..) of beam bolts are entered. The values to be entered are shown in the schematic drawing. |
Group 1 Beam bolts settings (number of lines, distance values ..) are entered. The values to be entered are shown in the schematic drawing. |
Bolt properties  The Hole and Bolt Parameters dialog is opened by clicking on the Bolt properties button . The bolt properties are set in this dialog. |
Schematic drawing  Connection and bolt placement values are shown on the schematic drawing. |
Preview There is a preview of the combination. The selection made and the entered values can be followed simultaneously in the preview. |
Weldings Tab
...
Specifications | |||||
|---|---|---|---|---|---|
Welds  The thickness, type and angle values of the welds to be made at the connections are given. The information on whether it will be done on the construction site or not is entered. | |||||
Weld electrode  The strengths of the welding electrodes are defined in the design inputs. The strength of the main element in the weld joint is controlled under the condition that it has less strength than the weld strength. If necessary, click the list and define "Create New…". To create the welding electrode, give the information "Name" and "Weld metal tensile strength" in the dialog that opens after clicking "Create New".
| |||||
Schematic drawing  Connection and source values are shown on the schematic drawing. | |||||
Preview  There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Design Data Tab
...
In the design data, the plate material is defined. The condition that the main element in the weld joint has less strength than the weld strength is controlled.
...
If necessary, click the list and define "Create New…". To create the welding electrodeplate material, give the information "Name" and "Strength" material definations and values in the dialog that opens after clicking "Create New".