This connection is a column and beam connection.
...
| Table of Contents |
|---|
With the Single Angle Connection command, column-beam connection is defined.
...
Location of the Single Angle Connection Command
...
Single Angle Connection Settings Dialog
Type and Placement Tab
Select the options given in the schematic representation according to the type of connection you want to make.
...
Angle Tab
The geometry of the angle used is given or one of the L profiles in the library can be used as a connection element with the Use Section option. If you check the plate geometry option, enter the plate dimensions according to the schematic representation.
...
Top Notch Tab
The notch geometry of the top of the beam element connected to the column is adjusted.
...
Bottom Notch Tab
The notch geometry of the bottom part of the beam element connected to the column is adjusted.
...
Support Bolts Tab
The properties of the bolts connecting the plate to the column are adjusted. The tab can be seen when the option with bolt to the support is selected from the type and layout tab.
...
Beam Bolts Tab
The properties of the bolts connecting the plate to the column are adjusted. The tab can be seen when the option with bolt to the support is selected from the type and layout tab.
...
Weldings Tab
The weld properties of the connections given in the schematic representation are set in the Welds tab. Give the size, type, angle values and mark the option whether to weld under construction site conditions.
...
...
Specifications |
|---|
Connection to support  Bolted or welded connection types are selected for the support connection. |
Connection to beam  Bolted or welded connection types are selected for the beam connection. |
Plates  It is chosen whether the plate will be on the left or right of the beam body. |
Orientation  One of the angled or straight options is chosen for the connection orientation. |
Placement  Placement values are entered. The values to be entered are shown in the schematic drawing. |
Schematic drawing  Connection and placement values are shown on the schematic drawing. |
Preview  There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Angle Tab
...
Specifications |
|---|
Define plate geometry  If the option is selected, it is determined by entering the angle values. The values to be entered are shown in the schematic drawing. |
Use section  By selecting the option, one of the ready-made L profiles is selected from the list as an angle bracket. By clicking on the load section button, you can reach the ready section library and reach the list of American and European finished rolling sections and select from the list. |
Length  Angle length value is entered. |
Schematic drawing  Connection and plate values are shown on the schematic drawing. |
Preview There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Top Notch Tab
...
Specifications |
|---|
Notch  If the option is selected, notching is done according to the entered values. The values to be entered are shown in the schematic drawing. |
Left flange cut  If the option is selected, left flange cutting is made according to the entered values. The values to be entered are shown in the schematic drawing. |
Right flange cut  If the option is selected, right flange cutting is made according to the entered values. The values to be entered are shown in the schematic drawing. |
Schematic drawing  Connection, notching and cutting values are shown on the schematic drawing. |
Preview There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Bottom Notch Tab
...
Specifications |
|---|
Notch If the option is selected, notching is done according to the entered values. The values to be entered are shown in the schematic drawing. |
Left flange cut If the option is selected, left flange cutting is made according to the entered values. The values to be entered are shown in the schematic drawing. |
Right flange cut If the option is selected, right flange cutting is made according to the entered values. The values to be entered are shown in the schematic drawing. |
Schematic drawing  Connection, notching and cutting values are shown on the schematic drawing. |
Preview There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Support Bolts Tab
...
Specifications |
|---|
Horizontal arrangement  Horizontal arrangement settings (number of horizontal bolt columns, distance values ..) of support bolts are entered. The values to be entered are shown in the schematic drawing. |
Group 1  Support bolts settings (number of lines, distance values ..) are entered. The values to be entered are shown in the schematic drawing. |
Bolt properties  The Hole and Bolt Parameters dialog is opened by clicking on the bolt properties button. The bolt properties are set in this dialog. |
Schematic drawing  Connection and bolt placement values are shown on the schematic drawing. |
Preview  There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Beam Bolts Tab
...
Specifications |
|---|
Horizontal arrangement Horizontal arrangement settings (number of horizontal bolt columns, distance values ..) of beam bolts are entered. The values to be entered are shown in the schematic drawing. |
Group 1 Beam bolts settings (number of lines, distance values ..) are entered. The values to be entered are shown in the schematic drawing. |
Bolt properties  The Hole and Bolt Parameters dialog is opened by clicking on the Bolt properties button . The bolt properties are set in this dialog. |
Schematic drawing  Connection and bolt placement values are shown on the schematic drawing. |
Preview There is a preview of the combination. The selection made and the entered values can be followed simultaneously in the preview. |
Weldings Tab
...
Specifications |
|---|
Welds  The thickness, type and angle values of the welds to be made at the connections are given. The information on whether it will be done on the construction site or not is entered. |
Weld electrode  The strengths of the welding electrodes are defined in the design inputs. The strength of the main element in the weld joint is controlled under the condition that it has less strength than the weld strength. If necessary, click the list and define "Create New…". To create the welding electrode, give the information "Name" and "Weld metal tensile strength" in the dialog that opens after clicking "Create New". Welding geometry is determined automatically by the program. These properties can be changed to easily determine the connection properties. Geometry features are in accordance with industry standards and in the form specified in AISC. Welding geometry is determined automatically by the program. These properties can be changed to easily determine the connection properties. Geometry features are in accordance with industry standards and in the form specified in AISC. |
Schematic drawing  Connection and source values are shown on the schematic drawing. |
Preview  There is a preview of the connection. The selection made and the entered values can be followed simultaneously in the preview. |
Design Data Tab
...
In the design data, the plate connection elements material is defined. The condition that the main element in the weld joint has less strength than the weld strength is controlled.
...
If necessary, click the list and define "Create New…". To create the welding electrodeconnection elements material, give the information "Name" and "Strength" material definitions and values in the dialog that opens after clicking "Create New".
...
Next Topic