Slab Reinforcements

Summary Information

The summary information about the line where the cursor is located is given in the name of the dialog in the format of Story, Name, Calculation Axis No, Operation Type, Rebar type.

Open

For example, Story 3, D1, 1, Double-way short, straight + bent-up

Using the Shift key

In this tab, you can select more than one row with the Shift key, enter a value by double-clicking any cell whose value is open to change, and make that value apply to all selected rows.

Using the Ctrl key

Ctrl key, on the other hand, selects the lines in between one by one.

All Stories

It lists the slabs on the screen throughout the entire story.

Show horizontals

It displays the horizontal rebars in the slabs by filtering, the vertical rebars are hidden, not shown in the list.

Show verticals

It displays the vertical rebars in the slabs by filtering, the horizontal rebars are hidden, not shown in the list.

Select

Selects the object on the line with the cursor. When the concrete dialog is closed, you can take action for the selected element.

Previous

The cursor moves to the previous line.

Next

The cursor goes to the next line.

Filter

It is used to define certain conditions and filter only the elements that satisfy that condition.

Ok

It saves the changes made and closes the dialog.

Cancel

Closes the dialog without saving the changes made.

DS

It is the rebar fixing column. If marked, the rebars are fixed. DS is automatically marked when changes are made to the slab rebars and the rebars remain fixed even if the slab is made of concrete. If DS is not marked, the rebars are determined again after the analysis according to the rebar selection conditions.

ID

It is the name of the story that appears in the plan. With the dialog open, double click the name cell to find the slab in the plan.

(D1, D2, D10 etc.) In case of negativity, a term about negativity is added next to the name of the record. For example, D101 (Min) will appear.

Thickness

The thickness of the slab appears in this cell.

Story

The name of the story where the slab is located appears in this cell.

N

It is the number of concrete calculation axis. (1,2,3,4 etc.) There can be more than one concrete calculation axis in the same slab. Slabs with the same name appear one under the other with the numbers of different account axes. From the N column, you can follow the direction of the calculation axis.

L upper aux

The diameter and the spacing in cm of the additional rebar calculated above the left support section on the relevant concrete calculation axis are shown. If double clicked on the cell, the diameter and spacing of the rebar can be changed.

Upper straight

It is the diameter and interval in cm of the rebar located above the slab section in the relevant concrete calculation axis. The diameter and spacing of the rebar can be changed by double clicking on the cell.

Bent-up

It is the diameter and interval in cm of the pleat rebar with slab on the relevant concrete calculation axis. The diameter and spacing of the rebar can be changed by double clicking on the cell.

Under straight

It is the diameter and interval in cm of the rebar located under the slab section on the relevant concrete calculation axis. The diameter and spacing of the rebar can be changed by double clicking on the cell.

R upper aux

It is the diameter and interval in cm of the additional rebar calculated above the right support section in the relevant concrete calculation axis. The diameter and spacing of the rebar can be changed by double clicking on the cell.

Left (upper)

Defines the upper part of the section belonging to the left support of the slab for the investigated concrete calculation axis.

Span (under)

It defines the lower part of the section in the slab opening in the analyzed concrete calculation axis.

Span (upper)

It defines the upper part of the section in the slab opening in the analyzed reinforced concrete calculation axis.

Right (upper)

It defines the upper part of the section belonging to the right support of the slab in the analyzed concrete calculation axis.

Moment

The design moment value that is taken as basis in concrete design is given.

As (Calculated)

It is the area of ​​rebar found for a width of 100 centimeters from the design moment.

As (Required)

It is the rebar area calculated from the design moment and the one that is greater than the rebar area to be placed as per the regulation.

As (Existing)

It is the total rebar area value available in the section after the rebar selection.

Load combination

You can examine the moment diagram by choosing the combination you want from the combination list.

Structural material

Shows the structural material of the slab.

fck

The characteristic of concrete is its compressive strength.

fcd

The characteristic calculation of concrete is its compressive strength.

fctd

The characteristic calculation of concrete is its tensile strength.

Rebar fyk

Reinforcement is the yield strength of rebar.

fyd

It is the calculation strength of rebar steel.

Moment diagram

The moment diagram according to the selected combination is displayed on the analyzed calculation axis. When you move the mouse over the moment diagram, the position of the cursor on the diagram is shown. X represents the Y moment value for the left distance.

N

It is the number of the addition. It is assigned automatically by the program.

Type

Indicates the location of the additional rebar. If it is lower, additional rebar is at the bottom, if it is over, additional rebar is at the top.

Location X

It is the distance of the region where the additional rebar is located to the global y-axis.

Location Y

It is the distance of the region where the additional rebar is located to the global x-axis.

Width

It is the width of the region where the additional rebar is located.

Length

It is the height of the area where the additional rebar is located.

Reinforcement

It is the diameter and range of the additional rebar to be placed in the region where the additional rebar is located.

Count

It is the number of additional rebar to be placed in the area where the additional rebar is located.

Req. As

In the area where additional rebar is located, it is the area of ​​rebar greater than the amount of rebar that should be placed after the renar design or as required by the regulation.

Existing As.

It is the amount of rebar placed in the area of ​​additional rebar.

Design moment

It is the design moment that gives the greatest rebar in the area where the additional rebar is located.

Design load

The most unfavorable loading type in which the design moment is calculated is written.

Combine selected areas

Selected additional rebar areas from the list are combined.

Show top & bottom rebars

If the option is selected, top and bottom additional rebars are shown.

Show top rebars

If the option is selected, top additional rebars are shown.

Show bottom rebars

If the option is selected, bottom additional rebars are shown.